The table features a ribbed base, milled work area with T slots. The column is bright nickel-plated. Powerful, long life 230V permanent magnet motor. The quill is driven via a Poly-V belt and three step pulleys. This yields a torque mulitplication of as much as 6x at the lowest speed. Geared quill feed for exact operations runs in ball bearings. Spindle with ½ thread accepts the standard chuck, as well as the optional collets.Technical data: 230V motor Spindle speeds 1080, 3100 and 6400 rpmQuill travel 63 mmHeadstock travel via the crank 70 mmThroat of 140 mmMaximum drill bit size 10 mm, which is also the capacity in stee, the optional collets offer a capacity to 6 mm Usable table size 200 x 200 mmColumn: 45 x 500 mmWeight: ca. 11 kg

For polishing metal, galss, precious metal, porcelain and plastic. Consits of :3 felt polishing bits (cylinder, cone, wheel)3 silicon polishing bits (bullet, cylinder and wheel)1 cotton polishing wheel1 chamois buffing wheel and 1 polishing pasteIncl. 2.35 x 44 mm arbor

Particularly suitable for precise sanding work on hard material.Long service life due to diamond coating. The set contains 30 profiles suitable for a wide range of work and is supplied in a matching storage case. By purchasing the 3-jaw drill chuck (W 941) also suitable for all MICROMOT devices.- Shank length: 45 mm- Diameter: 2.35 mmHead shapes: cylindrical, conical, roller, ball, point, wheel, cone and bud.

for polishing metal, gold, silver brass and aluminium when using polishing paste (W 96)10 pces

Two trays 50 x 76 x 15 mm - to keep insertable trays (e.g. grinding pencils, brushes etc., shaft 2,35 - 3,0 and 3,2 mm/1,8'')Insertable tools not included!

Die-cast zinc. With three machined sides. The slot fits the adjustable fence of the drill stand MB 140/S. Horizontal and vertical V-slots in jaw. Perfect for W37Jaw width: 50 mmJaw height: 10 mmMaximum clamping width: 34 mm

Head with dovetail guides can be tilted through 90° (scale ring available). Enables bevelled drilling and versatile milling operations. Geared rack and pinion feed with return spring allowing effortless and sensitive operation. Practical drill depth scale with adjustable limit stop (maximum travel 40 mm). With standard 20 mm collar for MICROMOT drilling and milling devices. With solid, hard chromium-plated steel column (280 x 20 mm), throat capacity (column inside to centre of tool) 140 mm. Plane-milled table (220 x 120 mm) with parallel limit stop and scale. Weight approx. 2.2 kg.

With a diameter of only 35mm and its low weight (230g) it offers convenient handling second to none in its class. The balanced motor effortlessly drives the ground ball bearing spindle allowing for a quiet run with a pleasant sound. High-quality MICROMOT steel collets ensure accurate clamping of even the smallest shafts, without rattling or vibrating of bits and cutters.A mains adapter is required to operate the MICROMOT 60 devices. We recommend the PROXXON mains adapter W26 odr W27.For milling, drilling, routing, de-scaling, polishing, cutting, cleaning, swing, engraving, etc. Useable on any workable material e.g. steel, precious metals, glass, ceramics, plastics, precious stones etc. High precision: ball bearing spindle. Special, balanced, low noise DC motor with high life expectancy. Variable electronic speed control with feedback effect (high engine power in the lower revolutions are). Housing of glass-fibre reinforced POLYAMIDE with soft component in the finger grip area. 20 mm collar for fitting MICROMOT accessories. Six MICROMOT collets (1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2 mm) are supplied.Technical data:Direct voltage: 12-18 VPower consumption: 40W max.Stroke speed: 5.000 - 20.000 rpmLength: ca. 220 mmWeight: ca. 230 gWith thyristor electronic speed controlUse of a transformer (W26 or W27) is required.1.) The standard 20mm collar allows use in the drill stands MB 140/S and MB 200 as well as in the universal holder UHZ.2.) Stable housing of glass-fibre reinforced POLYAMIDE. With a soft component in the finger grip area.3.) Infinitely variable electronic speed control with feedback effect. For high engine power also at lower speeds.Note: The speed control of our 12 volt devices only works when operated via nonstabilised power supply units (e.g. all MICROMOT mains adapters). Connection to stabilised power supply units is possible. However, the devices will then operate with maximum rotational speeds (also applies to operation with batteries).

Dual ball-bearinged milled steel shaft with tool holder for MICROMOT steel collets. Ball-bearinged shaft end on machine. Highly flexible core (does not run hot when working with tight radii). Length 100cmFor a maximum of 25,000 rpmIncludes 6 steel collets (1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2 mm)

Without speed control For W 31! (Micromot 60/E)Technical data:Capacity 2,0 A at 16 V open circuit – and 12 V under load = 24VA (DC)Polarised socket for MICROMOT plugInsulated to class 2 requirementsWeight: ca. 1,0 kg

With speed control! For devices without electrical speed control! Compact housing made of NORYL (particularly heat-resistant and approved for transformers). 3 sockets for MICROMOT connectors. 1 universal connector for normal banana plugs (Ø 4 mm). Main switch to switch off. Red LED display for operational readiness. Holes for storing insert tools with 2.35 and 3mm shanks. Foldable storage bracket for the MICROMOT device. Technical data: 220-240V. Delivers 2.0A at 16V idle and 12V operating voltage. Weight 1000g. Class 2 protective insulation.

Fits all Micromot machines1,0 - 1,5 - 2,0 - 2,4 - 3,0 and 3,2 mm (closure nut and holder are included)

Model building and engraving set with micromot mill/drill unit 60/E (separatly available: W31).Includes 34 industrial quality cutters: 1 diamond grinding bit, 1 fine milling bit 0,5 and 1,0 mm micro-drills, 1 brass brush, 4 carborundum grinding bits (cylinder, sphere, disc and cone shaped), 1 saw blade, 4 grinding wheels 22 x 3 mm (2 carborundum, 2 silicon carbide), 20 cutting disks and 1 arbor.With mains adapter for 220/240V operation (12V, 1,0A)Packed in a durable plastic case

essential for polishing metal and plasticjar: ca. 25 g

Powerful, quiet and durable.The maximum speed of 22,000 rpm can be steplessly reduced to 5,000 rpm with almost the same torque in the lower speed range. This is particularly important for micro drilling, brushing and polishing. The tool's spindle is supported by ball bearings and lockable for tool change at the push of a button. 20 mm system fit for use in MICROMOT drill stands and horizontal stands. Balanced DC motor with a low noise level and high life expectancy.  Sturdy housing made of fiberglass-reinforced POLYAMIDE with soft component in the handle area.Complete with 43 high-quality insert bits in a case made of high-quality PP.Technical data:- 5,000 - 22,000/min.- Power consumption: max. 100 W.- Voltage: 230 V- Length: 200 mm- Weight: 450 g- Protective insulation according to class 2

This high-revving, special, balanced low noise DC motor has full-wave electronic speed control. The ground steel spindle runs in a ball bearing. Stable head of die-cast aluminium and main housing of glass-fibre reinforced POLYAMIDE. The 20 mm MICROMOT collar allows fitting of optional drill stands, horizontal stands, etc.Includes 34 industrial quality cutters and six high concentricity MICROMOT collets (1.0 - 1.5 - 2.0 - 2.4 - 3.0 and 3.2 mm) and closure nut are included. Technical data:Speed: 5,000 - 20,000 rpmPower consumption: max. 100W, 220 - 240VLength: 230 mmWeight: ca. 500 gInsulated to class 2 requirements

High quality components for best operation. For cleaning, sanding, frosting, rounding-off and fine polishing of metal (incl. non ferous), precious metals, plastic, stone and wood.• shaft Ø2,35 mm

Used on all Micromot machinesCaspacity is 0,5-3,2 mm

Purpose made of stable construction with head and shaft out of a single blank. The precise flutes and optimal concentricity ensure best life expectancy. Diameter 2,3 and 3,1 mm. For use on hard and soft woods, NF and precious metals, as well as plastics and plaster of paris. Ideal for milling, routing, shaping, profiling and slotting.